{"id":597,"date":"2017-09-08T22:42:48","date_gmt":"2017-09-08T20:42:48","guid":{"rendered":"https:\/\/pssrc.org\/wordpress\/?p=597"},"modified":"2022-09-03T22:54:02","modified_gmt":"2022-09-03T20:54:02","slug":"controlled-expansion-of-supercritical-solutions-an-alternative-method-for-producing-nanoparticles-with-supercritical-carbon-dioxide","status":"publish","type":"post","link":"https:\/\/pssrc.org\/wordpress\/controlled-expansion-of-supercritical-solutions-an-alternative-method-for-producing-nanoparticles-with-supercritical-carbon-dioxide\/","title":{"rendered":"Controlled expansion of supercritical solutions: an alternative method for producing nanoparticles with supercritical carbon dioxide"},"content":{"rendered":"<p>Written by Jenni Pessi<!--more--><\/p>\n<p><strong>Background<\/strong><\/p>\n<p>Particle production based on supercritical carbon dioxide (scCO<sub>2<\/sub>) is efficient, inexpensive, and ecological [1]. These kinds of bottom-up technologies form particles by re-crystallization. CO<sub>2 <\/sub>is the most common solvent in supercritical processes, since its critical temperature and pressure are relatively low, 74 bar and 31\u00b0C [2]. Furthermore, CO<sub>2 <\/sub>is \u2018Generally Recognized As Safe\u2019 (GRAS) by FDA; it is neither flammable nor toxic.<\/p>\n<p>Particle production techniques employing scCO<sub>2 <\/sub>use scCO<sub>2<\/sub> as solvent, as solute or as anti-solvent [3]. Rapid Expansion of Supercritical Solutions (RESS) is a solvent- and excipient-free production method [4]. It has been mainly used to produce micron and submicron particles in pharmaceutics.<\/p>\n<p>The processes using scCO<sub>2<\/sub> as a solvent have been modified by changing process parameters. However, since invented, particle production using scCO<sub>2<\/sub> as solvent is based on rapidly decreasing the pressure [5]. The rapid decrease of pressure has been considered essential for formation of small particles.<\/p>\n<p><strong>Method<\/strong><\/p>\n<p>Our experiments indicate that nanoscale particles can be produced in opposite conditions to the existing RESS technique: <em>slow depressurization and with low degree of supersaturation<\/em>, using a method called Controlled Expansion of Supercritical Solution (CESS). Experimental apparatus was built for CESS experiments (<strong>Figure 1<\/strong>). CESS differs from RESS \u00a0in many respects and employs controlled mass transfer, controlled flow, controlled pressure reduction, and finally particle collection in dry ice (<strong>Table 1<\/strong>). The core of the technology is to allow larger initial nuclei size and particle growth by condensation. This avoids the variation in temperature, pressure, and density, as well as the particle growth by coagulation.<\/p>\n<p><img loading=\"lazy\" decoding=\"async\" class=\"alignnone size-full wp-image-600\" src=\"https:\/\/pssrc.org\/wordpress\/wp-content\/uploads\/2022\/09\/Fig1.jpg\" alt=\"\" width=\"915\" height=\"970\" srcset=\"https:\/\/pssrc.org\/wordpress\/wp-content\/uploads\/2022\/09\/Fig1.jpg 915w, https:\/\/pssrc.org\/wordpress\/wp-content\/uploads\/2022\/09\/Fig1-283x300.jpg 283w, https:\/\/pssrc.org\/wordpress\/wp-content\/uploads\/2022\/09\/Fig1-768x814.jpg 768w, https:\/\/pssrc.org\/wordpress\/wp-content\/uploads\/2022\/09\/Fig1-880x933.jpg 880w\" sizes=\"auto, (max-width: 915px) 100vw, 915px\" \/><\/p>\n<p><strong><em>Figure 1. <\/em><\/strong><em>Experimental apparatus used to produce nanoparticles.<\/em><\/p>\n<p>&nbsp;<\/p>\n<p><strong><em>Table 1. <\/em><\/strong><em>Essential differences between RESS and CESS techniques.<\/em><\/p>\n<table width=\"0\">\n<tbody>\n<tr>\n<td width=\"271\">&nbsp;<\/td>\n<td width=\"186\">RESS<\/td>\n<td width=\"210\">CESS<\/td>\n<\/tr>\n<tr>\n<td width=\"271\">Pressure drop<\/td>\n<td width=\"186\">rapid<\/td>\n<td width=\"210\">controlled<\/td>\n<\/tr>\n<tr>\n<td width=\"271\">Ratio of pressure drop<\/td>\n<td width=\"186\">&gt;10<\/td>\n<td width=\"210\">&lt;10<\/td>\n<\/tr>\n<tr>\n<td width=\"271\">Flow velocities<\/td>\n<td width=\"186\">supersonic<\/td>\n<td width=\"210\">subsonic<\/td>\n<\/tr>\n<tr>\n<td width=\"271\">Degree of supersaturation<\/td>\n<td width=\"186\">high<\/td>\n<td width=\"210\">low<\/td>\n<\/tr>\n<tr>\n<td width=\"271\">Formation of Mach disk<\/td>\n<td width=\"186\">yes<\/td>\n<td width=\"210\">no<\/td>\n<\/tr>\n<tr>\n<td width=\"271\">Particle formation<\/td>\n<td width=\"186\">mainly beyond exit nozzle<\/td>\n<td width=\"210\">mainly prior to exit nozzle<\/td>\n<\/tr>\n<tr>\n<td width=\"271\">Main mechanism for particle growth<\/td>\n<td width=\"186\">coagulation<\/td>\n<td width=\"210\">condensation<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<p>&nbsp;<\/p>\n<p>In RESS the supercritical solution is expanded through a nozzle and the subsequent rapid decrease in solvent density reduces the solvent power [4]. Particles are generated as solute precipitates and the particle formation, the creation of a single spherical particle of radius <em>r<\/em>, can be understood using the reduced Gibbs energy in a closed system (<strong>Equation 1<\/strong>) [6].<\/p>\n<figure id=\"attachment_598\" aria-describedby=\"caption-attachment-598\" style=\"width: 1386px\" class=\"wp-caption alignnone\"><img loading=\"lazy\" decoding=\"async\" class=\"wp-image-598 size-full\" src=\"https:\/\/pssrc.org\/wordpress\/wp-content\/uploads\/2022\/09\/eq1-1.png\" alt=\"\" width=\"1386\" height=\"115\" srcset=\"https:\/\/pssrc.org\/wordpress\/wp-content\/uploads\/2022\/09\/eq1-1.png 1386w, https:\/\/pssrc.org\/wordpress\/wp-content\/uploads\/2022\/09\/eq1-1-300x25.png 300w, https:\/\/pssrc.org\/wordpress\/wp-content\/uploads\/2022\/09\/eq1-1-1024x85.png 1024w, https:\/\/pssrc.org\/wordpress\/wp-content\/uploads\/2022\/09\/eq1-1-768x64.png 768w, https:\/\/pssrc.org\/wordpress\/wp-content\/uploads\/2022\/09\/eq1-1-1218x101.png 1218w, https:\/\/pssrc.org\/wordpress\/wp-content\/uploads\/2022\/09\/eq1-1-880x73.png 880w\" sizes=\"auto, (max-width: 1386px) 100vw, 1386px\" \/><figcaption id=\"caption-attachment-598\" class=\"wp-caption-text\">equation 1<\/figcaption><\/figure>\n<p>Here <em>\u0394<\/em><em>G<\/em>(<em>kT<\/em>)<sup>-1<\/sup> is the reduced Gibbs energy, <em>k<\/em> Bolzmann\u2019s constant, <em>T<\/em> temperature, \u03c3 the interfacial tension of the solute, <em>v<sub>2,s<\/sub><\/em> the molecular volume of the solid phase, <em>p<\/em><sub>2<\/sub> the partial pressure of the solute, and <em>S<\/em> the supersaturation. The parameter to alter in the expansion of a supercritical process is the supersaturation (<strong>Equation 2<\/strong>) [7].<\/p>\n<figure id=\"attachment_599\" aria-describedby=\"caption-attachment-599\" style=\"width: 1386px\" class=\"wp-caption alignnone\"><img loading=\"lazy\" decoding=\"async\" class=\"wp-image-599 size-full\" src=\"https:\/\/pssrc.org\/wordpress\/wp-content\/uploads\/2022\/09\/eq2.png\" alt=\"\" width=\"1386\" height=\"111\" srcset=\"https:\/\/pssrc.org\/wordpress\/wp-content\/uploads\/2022\/09\/eq2.png 1386w, https:\/\/pssrc.org\/wordpress\/wp-content\/uploads\/2022\/09\/eq2-300x24.png 300w, https:\/\/pssrc.org\/wordpress\/wp-content\/uploads\/2022\/09\/eq2-1024x82.png 1024w, https:\/\/pssrc.org\/wordpress\/wp-content\/uploads\/2022\/09\/eq2-768x62.png 768w, https:\/\/pssrc.org\/wordpress\/wp-content\/uploads\/2022\/09\/eq2-1218x98.png 1218w, https:\/\/pssrc.org\/wordpress\/wp-content\/uploads\/2022\/09\/eq2-880x70.png 880w\" sizes=\"auto, (max-width: 1386px) 100vw, 1386px\" \/><figcaption id=\"caption-attachment-599\" class=\"wp-caption-text\">equation 2<\/figcaption><\/figure>\n<p>Here, <em>y<sub>2,E<\/sub><\/em><sub>(<\/sub><em>T<sub>E<\/sub>,p<sub>E<\/sub><\/em>) is the mole fraction of the solute at post-expansion temperature and pressure, <em>y<\/em><sub>*2<\/sub>(<em>T, p<\/em>) is the equilibrium mole fraction of the solute at the extraction temperature and pressure, and \u00a0\u03a6<sub>2<\/sub> the solute fugacity coefficient relating the ideal gas pressure and the effective pressure of a real gas. The molar ratios determining the degree of supersaturation directly depend on the pre- and post-expansion pressure and temperature. A steep drop in pressure and temperature decreases the density and solvent power of CO<sub>2<\/sub> significantly, resulting in a high degree of supersaturation. The higher the degree of supersaturation, the more numerous and smaller are the formed nuclei [8].<\/p>\n<p>After nuclei formation, particles grow by two mechanisms: condensation where free molecules are deposited onto the nuclei surface, and coagulation where particles grow by colliding [9]. In RESS the time available for particle growth by condensation is limited to microseconds.<\/p>\n<p>In RESS, the ratio of pre-expansion to post-expansion pressures exceeds 10, the ejection velocity is sonic at the nozzle, and later supersonic [10]. The supersonic free jet ends with a Mach disk beyond which the velocities again are subsonic. \u00a0Particle precipitation in the RESS process mainly takes place after the nozzle exit and in the shear layer of the jet [11]. The particle concentration is highest at the Mach disk and the main mechanism for particle growth is coagulation in the subsonic free jet. The flow in the collection chamber of a RESS system is often rather chaotic.<\/p>\n<p>In CESS the focus is on achieving lower degrees of supersaturation, slow velocity and limited mass transfer. The ratio of pressure before and after each pressure drop is kept below ten. This prevents the flow speed beyond the nozzle from reaching sonic velocity, and thus there is neither a Mach disk nor density differences in the collection chamber as in the RESS process. Consequently, particle growth by coagulation is reduced. Particles form under mild conditions prior to the exit nozzle and grow mainly by condensation. Particle formation and growth is thus much slower than in RESS and the particles form in a controlled environment.<\/p>\n<p>The CESS process itself is more robust, stable, and reproducible, than the RESS process; the pressure and flow as well as the production rate are constant and the environment for particle formation between processes is identical. In contrast to RESS, small changes in the initial pressure and temperature do not affect the end-product. The CESS process produces small particles successfully without use of co-solvents, excipients, or collection into aqueous media.<\/p>\n<p>&nbsp;<\/p>\n<p><strong>Results<\/strong><\/p>\n<p>The pressure, flow, and the rate of solid dispersion formation within the collection chamber are constant. Hence the collection and particle production processes are stable. The robustness, stability, and reproducibility of the process were proven by preparing 3 batches of the same product. The SEM images obtained from different parts of each sample indicate that the nanoparticles prepared from piroxicam were monodisperse in size and shape. The average nanoparticle diameter was 176 nm \u00b1 53 nm, the batches 169 \u00b1 48 nm (<em>n<\/em>=300), 179 nm \u00b1 54 nm (<em>n<\/em>=300), and 179 nm \u00b1 67 nm (<em>n<\/em>=300) (<strong>Figure 2<\/strong>). The particle size of the bulk was 7106 \u00b1 5639 nm (<em>n<\/em>=300).<\/p>\n<p><img loading=\"lazy\" decoding=\"async\" class=\"alignnone size-full wp-image-601\" src=\"https:\/\/pssrc.org\/wordpress\/wp-content\/uploads\/2022\/09\/fig2-2.png\" alt=\"\" width=\"1386\" height=\"500\" srcset=\"https:\/\/pssrc.org\/wordpress\/wp-content\/uploads\/2022\/09\/fig2-2.png 1386w, https:\/\/pssrc.org\/wordpress\/wp-content\/uploads\/2022\/09\/fig2-2-300x108.png 300w, https:\/\/pssrc.org\/wordpress\/wp-content\/uploads\/2022\/09\/fig2-2-1024x369.png 1024w, https:\/\/pssrc.org\/wordpress\/wp-content\/uploads\/2022\/09\/fig2-2-768x277.png 768w, https:\/\/pssrc.org\/wordpress\/wp-content\/uploads\/2022\/09\/fig2-2-1218x439.png 1218w, https:\/\/pssrc.org\/wordpress\/wp-content\/uploads\/2022\/09\/fig2-2-880x317.png 880w\" sizes=\"auto, (max-width: 1386px) 100vw, 1386px\" \/><\/p>\n<p><strong><em>Figure 2. <\/em><\/strong><em>Nanoparticles and bulk piroxicam: a) batch 1, b) batch 2, c) batch 3, and d) bulk piroxicam. The size bar is 5 \u00b5m. Particle size distributions with mean particle size and standard deviations for a) batch 1, b) batch 2, and c)\u00a0batch\u00a03.<\/em><\/p>\n<p><strong>\u00a0<\/strong><\/p>\n<p><strong>Conclusions<\/strong><\/p>\n<p>We established a crystallization process that employs scCO<sub>2<\/sub> and that offers significant advantages compared to existing scCO<sub>2<\/sub> techniques. Controlled Expansion of Supercritical Solutions (CESS) with two-step gradient pressure reduction permits producing pure drug nanoparticles with narrow size-distribution.<\/p>\n<p>&nbsp;<\/p>\n<p><strong>Acknowledgements<\/strong><\/p>\n<p>The article is based on the publication \u201cControlled Expansion of Supercritical Solution (CESS): a robust method to produce pure drug nanoparticles with narrow size-distribution\u201d (J Pharm Sci 2016; 105(8); 2293-2297) by Jenni Pessi, Ilkka Lassila, Antti Meril\u00e4inen, Heikki R\u00e4ikk\u00f6nen, Edward H\u00e6ggstr\u00f6m and JoukoYliruusi. Jenni Pessi, Heikki R\u00e4ikk\u00f6nen and JoukoYliruusi are from the Formulation and Industrial Pharmacy Unit of Division of Pharmaceutical Chemistry and Technology, Faculty of Pharmacy, University of Helsinki. Ilkka Lassila, Antti Meril\u00e4inen and Edward H\u00e6ggstr\u00f6m are from the Division of Material Physics, Department of Physics, University of Helsinki.<\/p>\n<p>&nbsp;<\/p>\n<p><strong>Formulation and Industrial Pharmacy (FIP) <\/strong><\/p>\n<p>The FIP research unit focuses on the translation of a drug molecule into a medicine. The aim is to maximise the quality and feasibility of the medicine by understanding all the factors that affect product development, including pharmaceutical material properties, processing, stability, and end user needs. Research focuses of FIP are solid state engineering, molecular based formulation science, processing technology, and industrial pharmacy research.<\/p>\n<p>&nbsp;<\/p>\n<p><strong>References<\/strong><\/p>\n<ol>\n<li>Fages J, Lochard H, Letourneau J-J, Sauceau M, Rodier E 2004. Particle generation for pharmaceutical applications using supercritical fluid technology. Powder Technology 141(3):219-226.<\/li>\n<li>Pereda S, Bottini S, Brignole E. 2008. Fundamentals of Supercritical Fluid Technology. 1 ed., New York: Taylor &amp; Francis Group.<\/li>\n<li>York P 1999. Strategies for particle design using supercritical fluid technologies. Pharmaceutical science &amp; technology today 2(11):430-440.<\/li>\n<li>T\u00fcrk M. 2014. Basics of Particles Formation Processes. In T\u00fcrk M, editor Particle Formation with Supercritical Fluids: Challenges and Limitations, 1 ed., Amsterdam, Netherlands: Elsevier. p 45-75.<\/li>\n<li>Jung J, Perrut M 2001. Particle design using supercritical fluids: literature and patent survey. The Journal of Supercritical Fluids 20(3):179-219.<\/li>\n<li>Springer GS 1978. Homogeneous nucleation. Advances in Heat Transfer 14:281-346.<\/li>\n<li>Debenedetti P, Kumar S 1986. Infinite dilution fugacity coefficients and the general behavior of dilute binary systems. AIChE journal 32(8):1253-1262.<\/li>\n<li>33. Debenedetti PG 1990. Homogeneous nucleation in supercritical fluids. AIChE Journal 36(9):1289-1298.<\/li>\n<li>Weber M, Thies MC 2007. A simplified and generalized model for the rapid expansion of supercritical solutions. The Journal of supercritical fluids 40(3):402-419.<\/li>\n<li>Helfgen B, T\u00fcrk M, Schaber K 2003. Hydrodynamic and aerosol modelling of the rapid expansion of supercritical solutions (RESS-process). The Journal of supercritical fluids 26(3):225-242.<\/li>\n<li>Liu J, Amberg G, Do-Quang M 2014. Numerical simulation of particle formation in the rapid expansion of supercritical solution process. The Journal of Supercritical Fluids 95:572-587<\/li>\n<\/ol>\n","protected":false},"excerpt":{"rendered":"<p>Written by Jenni Pessi<\/p>\n","protected":false},"author":1,"featured_media":602,"comment_status":"closed","ping_status":"closed","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[2],"tags":[40,39],"class_list":["post-597","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-research-highlights","tag-particle","tag-supercritical-carbon-dioxide","wpcat-2-id"],"_links":{"self":[{"href":"https:\/\/pssrc.org\/wordpress\/wp-json\/wp\/v2\/posts\/597","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/pssrc.org\/wordpress\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/pssrc.org\/wordpress\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/pssrc.org\/wordpress\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/pssrc.org\/wordpress\/wp-json\/wp\/v2\/comments?post=597"}],"version-history":[{"count":1,"href":"https:\/\/pssrc.org\/wordpress\/wp-json\/wp\/v2\/posts\/597\/revisions"}],"predecessor-version":[{"id":603,"href":"https:\/\/pssrc.org\/wordpress\/wp-json\/wp\/v2\/posts\/597\/revisions\/603"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/pssrc.org\/wordpress\/wp-json\/wp\/v2\/media\/602"}],"wp:attachment":[{"href":"https:\/\/pssrc.org\/wordpress\/wp-json\/wp\/v2\/media?parent=597"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/pssrc.org\/wordpress\/wp-json\/wp\/v2\/categories?post=597"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/pssrc.org\/wordpress\/wp-json\/wp\/v2\/tags?post=597"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}